Zip AP3/10 Aquapoint III White Plastic Unvented Undersink Water Heater 10Ltr 2kW 240V
Zip AP3/10 Aquapoint III is an unvented undersink water heater with 10 litre storage capacity to serve single or multiple hot water outlets. It has a glass lined steel storage tank tested to 12 bar and a sacrificial anode is fitted for protection against aggressive water conditions. All Zip Aquapoint III water heaters come with all the necessary accessories and factory fitted P&T valve. Zip Aquapoint III water heaters are a favourite choice of supplying hot water within a domestic or commercial environment.
within 1-2 working days
Zip Aquapoint III AP3/10 Description
Zip AP3/10 Aquapoint III is a 10 litre unvented undersink water heater suitable for serving single or multiple hot water outlets. It has a glass lined steel storage tank tested to 12 bar and a sacrificial anode is fitted for protection against aggressive water conditions. The tank comes equipped with a 2.0 kW heating element, guaranteeing a steady and efficient hot water supply.
Zip Aquapoint III AP3/10 has external temperature control with frost protection and is used with conventional taps or mixers. Safety features include a sacrificial anode, an adjustable thermostat with a range up to 75ºC, a resettable over-temperature safety cut-out, and high-density CFC-free polyurethane foam insulation.
Zip Aquapoint III 10 Litre Water Heater is supplied with an installation kit complete with wall mounting bracket.
Zip AP3/10 Water Heaters Features
- Capacity (L): 10
- Power rating (kW): 2.0
- Voltage Rating (V): 230
- Dimensions (mm): W350 D265 H480
- Weight (KG): 9.5
- Colour: white
- Control: electronic
- Inlet pipe 1/2"bsp
- Warranty: 1 Year
- Heating element: Embedded rod type
- Thermostat: Capillary type adjustable up to 7ºC to 75ºC.
- Water tank: 1.8mm glass enamelled, steel tested to 12 bar, with a working pressure of 3.5-4 bar
- Case: High impact and corrosion resistant white plastic.
- Insulation: High density, CFC-free polyurethane foam.
- IP Rating: IP24
- Approvals: WRAS approved and CE endorsed
Safety features
- manually resettable thermal cutout set to 85ºC +/– 3ºC.
- expansion relief valve (supplied) set at 6 bar.
- protected against frost whilst power is on.
- sacrificial anode for added protection against corrosion for element and tank – must be checked regularly (6 months) and replaced where necessary as gradual erosion will occur.
- In extreme cases local water conditions can cause rapid erosion of the anode resulting in particles being deposited as a residue.
- The Aquapoint should not be used where water quality is critical.
Warranty
One-year on site parts and labour
Installation
Separate models available for oversink and undersink installation.
All models can be wall mounted.
Undersink units can be installed unsupported on the floor if required.
All models can supply one outlet or multiple outlets, subject to capacity, without the need for special taps.
Plumbing
Water connections ½" / 15mm BSP.
Minimum recommended water pressure 1 bar.
Pressure relief valve (supplied) set at 6 bar.
Pressure and temperature relief valve requires plumbing to waste in accordance with water byelaws.
Should be installed only by a suitably experienced installer of unvented electric storage water heaters.
Oversink and undersink models not interchangeable
Electrical
To be wired to a double pole fused spur, minimum break rating 13 amps.
Installation must comply with current IEE regulations.
Supplied with 1 metre of pre-wired cable.
Caution
Variable temperature water heaters should be set only in strict compliance with regulations governing the temperature of stored and dispensed hot water.